Exfo AXS-200/850 Ethernet Test Set Bedienungsanleitung

User GuideEthernet Test SetAXS-200/850

RFC 254490 AXS-200/850GraphGraphGives the graph showing the Throughput, Back-to-Back, Frame Loss, or Latency measurement.Press , select RFC 2544, Resu

RFC 2544Ethernet Test Set 91Alarms/ErrorsAlarms/ErrorsPress , select RFC 2544, Results, and the Alarms/Errors tab.The Alarms/Errors page displays alar

RFC 254492 AXS-200/850Alarms/ErrorsThe Alarm LEDs are described as follows:LED Label Color MeaningLink Down Green Link up.Red Link down (Current).Ambe

RFC 2544Ethernet Test Set 93Alarms/ErrorsErrors³ Symbol (100/1000 Mbps): A Symbol Error is declared when an invalid code-group in the transmission cod

Ethernet Test Set 959BERTThe Bit Error Rate Test (BERT) measures the level of transmission impairment on a communication channel. Specific test patter

BERT96 AXS-200/850Unidirectional BERT testing is performed whereby the test stream is transmitted from the local module to a remote device in loopback

BERTEthernet Test Set 97Global ConfigurationGlobal ConfigurationThe rate and frame size can be changed dynamically while the test is running. The Pass

BERT98 AXS-200/850Global Configuration³ Frame Size (Bytes): Set the frame size up to 9600 bytes. The default value is 64 bytes. By default, No VLAN is

BERTEthernet Test Set 99Global Configuration³ Invert: Enable or disable Invert. If enabled, the test pattern is transmitted/analyzed with all bits inv

Ethernet Test Set 11 Introducing the AXS-200/850 Ethernet Test SetThe AXS-200/850 Ethernet Test Set provides Ethernet testing capability on the AXS-20

BERT100 AXS-200/850Global Configuration³ Pass/Fail Verdict: The Pass/Fail Verdict configuration enables or disables the use of the pass/fail verdict f

BERTEthernet Test Set 101Stream ConfigurationStream ConfigurationPress , select BERT, Configuration, and the Stream tab.Note: Only Destination MAC Add

BERT102 AXS-200/850Stream ConfigurationIf not resolved after 3 seconds, the MAC value becomes “--” and the stream is disabled. In the next status fiel

BERTEthernet Test Set 103Stream Configuration³ TOS/DS for IPv4 and Traffic Class (TOS/DS) for IPv6Select Type of Service (TOS) or Differentiated Servi

BERT104 AXS-200/850Stream Configuration³ If DS is selected, go to the next field to enter the hexadecimal code 00 to FF or go to the field underneath

BERTEthernet Test Set 105Summary ResultsSummary ResultsThe Summary Results page allows the user to not only view the status of the test, but to also c

BERT106 AXS-200/850Summary Results³ Start Time: The time when the BERT test was started.³ Duration: The length of time from when the test was started,

BERTEthernet Test Set 107Summary Results³ BER Threshold: Enter the threshold amount as follows (if the bit error results exceed this value, the test w

BERT108 AXS-200/850Summary ResultsReport GenerationReports can be generated for the test and tools results. The report button is available on the BERT

BERTEthernet Test Set 109Summary Results6. Press the function key under Configuration on the bottom of the screen to configure the titles and headings

Introducing the AXS-200/850 Ethernet Test Set2 AXS-200/850Models³ One electrical interface supporting:10 Mbps100 Mbps1000 Mbps³ One optical interface

BERT110 AXS-200/850Summary Results9. Select View to display the changes on the report file.10. Select Save to save the report file.The report will be

BERTEthernet Test Set 111Detailed ResultsDetailed ResultsPress , select BERT, Results, and the Detailed tab.Alarms³ Pattern Loss: Alarm is raised when

BERT112 AXS-200/850Service Disruption ResultsService Disruption ResultsThe Service Disruption Results page allows the user to view the results and cha

BERTEthernet Test Set 113Service Disruption Results³ Average (ms): Displays the average service disruption time from the beginning of the test.³ Total

BERT114 AXS-200/850Alarms/ErrorsAlarms/ErrorsPress , select BERT, Results, and the Alarms/Errors tab.The Alarms/Errors page displays alarms and errors

BERTEthernet Test Set 115Alarms/ErrorsThe Alarm LEDs are described as follows:LED Label Color MeaningLink Down Green Link up.Red Link down (Current).A

BERT116 AXS-200/850Alarms/ErrorsErrors³ Symbol (100/1000 Mbps): A Symbol Error is declared when an invalid code-group in the transmission code is dete

BERTEthernet Test Set 117LoggerLoggerThe Logger page allows the user to configure and view the Logger events based on Event ID, Time, Event, Duration

BERT118 AXS-200/850Logger³ Log Full: Indicates that the logger exceeds its maximum of 500 entries. The Log Full indicator can have three conditions:Th

BERTEthernet Test Set 119LoggerThe following table displays the nature of information reported by type of event:Note: The alarm events will not displa

Introducing the AXS-200/850 Ethernet Test SetEthernet Test Set 3Software OptionsSoftware OptionsSoftware keys are available to enable additional servi

BERT120 AXS-200/850LoggerThe Event Logger information will be cleared under the following conditions:³ When the test is reset or started.³ When the un

BERTEthernet Test Set 121LoggerAuto-Scroll will be active when:³ The test is running.³ The latest event is being displayed.³ The Sort By parameter is

Ethernet Test Set 12310 Traffic Generation & MonitoringThe main goal of Traffic Generation & Monitoring test is to qualify the performance of

Traffic Generation & Monitoring124 AXS-200/850The Traffic Generation & Monitoring test offers the following structure:SubMenu Tab PageStream C

Traffic Generation & MonitoringEthernet Test Set 125Global ConfigurationGlobal ConfigurationThe Global page allows configuring the main stream pro

Traffic Generation & Monitoring126 AXS-200/850Global Configuration³ Frame Size (Bytes): Set the frame size for Ethernet and Ethernet/IPv4/UDP or E

Traffic Generation & MonitoringEthernet Test Set 127Global Configuration³ Throughput Pass/Fail Verdict: Select the type of Throughput Pass/Fail Ve

Traffic Generation & Monitoring128 AXS-200/850Shaping ConfigurationShaping ConfigurationThe main stream is configured to send frames evenly distri

Traffic Generation & MonitoringEthernet Test Set 129Shaping Configuration³ Ramp Nb. of Steps: Enter the number of steps in the ramp pattern. The a

Introducing the AXS-200/850 Ethernet Test Set4 AXS-200/850Optical Transceivers (SFP)Optical Transceivers (SFP)The following table lists the compatible

Traffic Generation & Monitoring130 AXS-200/850Stream ConfigurationStream ConfigurationThe Sequence Tracking parameter determines if proprietary in

Traffic Generation & MonitoringEthernet Test Set 131Stream ConfigurationWhen enabled, a Neighbor Solicitation request is sent to the network to re

Traffic Generation & Monitoring132 AXS-200/850Stream Configuration³ TTL for IPv4 and Hop Limit (TTL) for IPv6Enter the Time to Live (TTL) value. T

Traffic Generation & MonitoringEthernet Test Set 133Stream Configuration³ If DS is selected, go to the next field to enter the hexadecimal code 00

Traffic Generation & Monitoring134 AXS-200/850Sequence ConfigurationSequence ConfigurationThe Sequence Configuration page defines the sequence tra

Traffic Generation & MonitoringEthernet Test Set 135Sequence Configuration³ Out of Sequence Pass/Fail Verdict: Select the type of verdict for decl

Traffic Generation & Monitoring136 AXS-200/850Jitter/Latency ConfigurationJitter/Latency ConfigurationPress , select Traffic Generation & Moni

Traffic Generation & MonitoringEthernet Test Set 137Jitter/Latency Configuration³ The following pre-defined profiles are available when frame stru

Traffic Generation & Monitoring138 AXS-200/850Jitter/Latency ConfigurationFor IPv6:³ Jitter Pass/Fail Verdict: Enable Jitter Pass/Fail Verdict to

Traffic Generation & MonitoringEthernet Test Set 139Jitter/Latency ConfigurationLatency Configuration³ Latency: The Latency parameter allows to en

Introducing the AXS-200/850 Ethernet Test SetEthernet Test Set 5ConventionsConventionsBefore using the product described in this manual, you should un

Traffic Generation & Monitoring140 AXS-200/850Transmit ConfigurationTransmit ConfigurationThe transmit configuration allows to configure the backg

Traffic Generation & MonitoringEthernet Test Set 141Transmit ConfigurationThe following table displays the minimum and maximum frame size:³ Payloa

Traffic Generation & Monitoring142 AXS-200/850Stream ConfigurationStream ConfigurationThe stream configuration parameters define the Ethernet, UDP

Traffic Generation & MonitoringEthernet Test Set 143Stream Configuration³ Resolve MAC Address: Enable or disable Resolve MAC Address. The default

Traffic Generation & Monitoring144 AXS-200/850Stream Configuration³ Quick Ping: Select the Quick Ping button to test if destination IP address can

Traffic Generation & MonitoringEthernet Test Set 145Stream ConfigurationThe possible values are shown as follows:³ If DS is selected, go to the ne

Traffic Generation & Monitoring146 AXS-200/850Stream ConfigurationThe possible values are shown as follows:³ Flow Label (For IPv6 only): Enter the

Traffic Generation & MonitoringEthernet Test Set 147Network ConfigurationNetwork ConfigurationNetwork Configuration allows to configure the networ

Traffic Generation & Monitoring148 AXS-200/850Network ConfigurationWhen IPv6 version is selected, configure the following fields in the Stream tab

Traffic Generation & MonitoringEthernet Test Set 149Network Configuration³ StatelessAuto allows automatic generation the IPv6 address based on the

Traffic Generation & Monitoring150 AXS-200/850Network ConfigurationLink-Local/Global IPv6 Address StatusMode Status DescriptionStatelessAuto -- Un

Traffic Generation & MonitoringEthernet Test Set 151Default GatewayDefault GatewayThe Default Gateway tab allows the configuration of the default

Traffic Generation & Monitoring152 AXS-200/850Default GatewayDefault Gateway Address StatusStatus Description-- UndefinedChecking Detection in pro

Traffic Generation & MonitoringEthernet Test Set 153VLAN ConfigurationVLAN ConfigurationVLAN Configuration page allows the user to configure the l

Traffic Generation & Monitoring154 AXS-200/850Summary ResultsSummary ResultsPress , select Traffic Generation & Monitoring, Results, and the S

Traffic Generation & MonitoringEthernet Test Set 155Summary Results³ Frame Loss (F.Loss): A frame loss event is declared when a sequence number is

Traffic Generation & Monitoring156 AXS-200/850Summary ResultsThe Alarm LEDs are described as follows: ³ Duration: The length of time from when the

Traffic Generation & MonitoringEthernet Test Set 157Summary Results³ Jitter: The Jitter meter displays current Jitter Statistics of the main strea

Traffic Generation & Monitoring158 AXS-200/850Summary Results³ Frame size (Bytes): Set the frame size for Ethernet and Ethernet/IPv4/UDP or Ethern

Traffic Generation & MonitoringEthernet Test Set 159Summary ResultsNote: The frame size can be changed for Ethernet frames even when test is runni

Ethernet Test Set 72 Safety InformationLaser Safety WarningsWARNINGDo not install or terminate fibers while a laser source is active. Never look direc

Traffic Generation & Monitoring160 AXS-200/850Summary ResultsReport GenerationReports can be generated for the test and tools results. The report

Traffic Generation & MonitoringEthernet Test Set 161Summary Results6. Press the function key under Configuration on the bottom of the screen to co

Traffic Generation & Monitoring162 AXS-200/850Summary Results9. Select View to display the changes on the report file.10. Select Save to save the

Traffic Generation & MonitoringEthernet Test Set 163Throughput ResultsThroughput ResultsPress , select Traffic Generation & Monitoring, Result

Traffic Generation & Monitoring164 AXS-200/850Throughput ResultsNote: When the Throughput Pass/fail verdict is selected as the Current RX Rate, th

Traffic Generation & MonitoringEthernet Test Set 165Sequence ResultsSequence ResultsPress , select Traffic Generation & Monitoring, Results, a

Traffic Generation & Monitoring166 AXS-200/850Sequence ResultsThe Alarm LEDs are described as follows:LED Label ColorMeaningFrame Loss Green No fr

Traffic Generation & MonitoringEthernet Test Set 167Sequence ResultsStatistics for Out-Of-Sequence FramesOut-Of-Sequence is declared when a frame/

Traffic Generation & Monitoring168 AXS-200/850Sequence ResultsThe Alarm LEDs are described as follows:Statistics for Total Frame Count³ RX: Displa

Traffic Generation & MonitoringEthernet Test Set 169Jitter/Latency ResultsJitter/Latency ResultsPress , select Traffic Generation & Monitoring

Safety Information8 AXS-200/850Installation Instructions WarningsInstallation Instructions WarningsCAUTIONNo user serviceable parts are contained insi

Traffic Generation & Monitoring170 AXS-200/850Jitter/Latency ResultsLatency Statistics:³ Current: Displays average of the measured delay values of

Traffic Generation & MonitoringEthernet Test Set 171Alarms/Errors ResultsAlarms/Errors ResultsPress , select Traffic Generation & Monitoring,

Traffic Generation & Monitoring172 AXS-200/850Alarms/Errors ResultsThe Alarm LEDs are described as follows:Errors ³ Symbol: A symbol error is decl

Traffic Generation & MonitoringEthernet Test Set 173Alarms/Errors Results³ Runt: The number of received frames that are smaller than 64 bytes with

Traffic Generation & Monitoring174 AXS-200/850Frame Count ResultsFrame Count ResultsPress , select Traffic Generation & Monitoring, Results, a

Traffic Generation & MonitoringEthernet Test Set 175Frame Size ResultsFrame Size ResultsPress , select Traffic Generation & Monitoring, Result

Traffic Generation & Monitoring176 AXS-200/850Frame Size ResultsThe following table displays the received frame size count statistics: Frame size

Traffic Generation & MonitoringEthernet Test Set 177Flow Control ResultsFlow Control ResultsPress , select Traffic Generation & Monitoring, Re

Traffic Generation & Monitoring178 AXS-200/850LoggerLoggerThe Logger page allows the user to configure and view the Logger events based on Event I

Traffic Generation & MonitoringEthernet Test Set 179Logger³ Log Full: Indicates that the logger exceeds its maximum of 500 entries. The Log Full i

Ethernet Test Set 93 Getting StartedWindows CE 6.0 is the baseline operating system software and is pre-installed on the Sharp Tester. If the AXS-200/

Traffic Generation & Monitoring180 AXS-200/850LoggerThe following table displays the nature of information reported by type of event:Type of Event

Traffic Generation & MonitoringEthernet Test Set 181LoggerNote: The alarm events will not display any details.Note: The Logger table can display u

Traffic Generation & Monitoring182 AXS-200/850LoggerAuto-Scroll will be active when:³ The test is running.³ The latest event is being displayed.³

Ethernet Test Set 18311 Smart LoopbackThe Smart Loopback test allows looping back an Ethernet data stream simply based on the interface setup paramete

Ethernet Test Set 18512 ToolsThe tools available on the AXS-200/850 Ethernet Test Set are Ping, Trace Route, and Report. The Tools menu offers the fol

Tools186 AXS-200/850Ping ConfigurationPing ConfigurationThe Ping tool is used to determine if a network device is reachable.Press , select Tools, Ping

ToolsEthernet Test Set 187Ping ConfigurationWhen the IP Address field is selected for editing, the Latest IP’s button appears on the bottom of the scr

Tools188 AXS-200/850Ping ResultsPing ResultsPress , select Tools, Ping, and the Results tab.To succeed, a Ping command shall be acknowledged by the ne

ToolsEthernet Test Set 189Ping Results³ Status: Indicates the status of the attempt as follows:Status DescriptionSuccessful Valid ICMP echo reply rece

ii AXS-200/850Copyright © 2007–2009 EXFO Electro-Optical Engineering Inc. All rights reserved. No part of this publication may be reproduced, stored i

Tools190 AXS-200/850Ping Results³ Replied From: Indicates the IP address of the replier.³ Bytes: Indicates the buffer size of the ICMP echo response.³

ToolsEthernet Test Set 191Ping StatisticsPing StatisticsPress , select Tools, Ping, and the Statistics tab.³ Packets Transmitted: Indicates the number

Tools192 AXS-200/850Trace Route ConfigurationTrace Route ConfigurationTrace Route is used to obtain the list of all hops identified between the local

ToolsEthernet Test Set 193Trace Route ResultsTrace Route ResultsPress , select Tools, Trace Route, and the Results tab.To succeed, a Trace Route comma

Tools194 AXS-200/850Trace Route Results³ No.: Indicates the attempt number.³ Status: Indicates the status of the attempt.Status DescriptionSuccessful

ToolsEthernet Test Set 195Trace Route Results³ Replied From: Indicates the IP address of the replier.³ Time: Indicates the time of response in millise

Tools196 AXS-200/850Cable Test ConfigurationCable Test ConfigurationThe cable test tool is used to diagnose UTP twisted pairs cables (up to Category 6

ToolsEthernet Test Set 197Cable Test ConfigurationWiring Standard: Select the pin-to-pair assignment corresponding to the UTP cable used. Choices are

Tools198 AXS-200/850Cable Test Configuration³ Prop. Delay Threshold (ns): Set the threshold value as the maximum time for a pulse to reach the far end

ToolsEthernet Test Set 199Cable Test Results - SummaryCable Test Results - SummaryThe cable test result Summary tab gives the cable test status and Pa

Ethernet Test Set 114 Using the Smart User InterfaceKeypadRefer to the AXS-200 User Guide for more information on how to use the keypad. The naming co

Tools200 AXS-200/850Cable Test Results - SummaryDelay Skew (ns): Indicates the delay skew value for the pair having the worst delay skew. The Pass/Fai

ToolsEthernet Test Set 201Cable Test Results - Wire MapCable Test Results - Wire MapThe cable test result Wire Map tab gives the cable pinout, and con

Tools202 AXS-200/850Cable Test Results - Wire MapWire Map Test Result: Gives the wire map test result for each pair.When the link is up: The wire map

ToolsEthernet Test Set 203Cable Test Results - Wire MapWhen the link is down:Short: Short-circuit between Tip and Ring wires of a pair or Tip or ring

Tools204 AXS-200/850Cable Test Results - Wire Map³ Fault Dist. (m/ft): Gives the distance to fault from the near end for each pair, unless the problem

ToolsEthernet Test Set 205Cable Test Results - Delay/LengthCable Test Results - Delay/LengthThe cable test result Delay/Length tab gives the propagati

Tools206 AXS-200/850Cable Test Results - Delay/Length³ Prop. Delay (ns): Indicates the propagation delay of a signal through each pair.³ Length (m/ft)

ToolsEthernet Test Set 207Report ConfigurationReport ConfigurationThe configurable parameters appear on the top of the report page.Press , select Tool

Tools208 AXS-200/850Report Configuration³ Logger in Report: Allows to enable or disable the Logger section in Report. Choices are Enabled and Disabled

ToolsEthernet Test Set 209Report FileReport File Report files from the internal flash memory can be opened or deleted from this page.Press , select To

Using the Smart User Interface12 AXS-200/850Home MenuHome MenuUpon start up, the Home menu is displayed. Use the up and down navigation arrows to navi

Ethernet Test Set 21113 SystemThe System menu gives access to tabs containing functions related to the AXS-200. The System menu offers the following s

System212 AXS-200/850File ManagerFile ManagerThe File Manager allows files and folders to be copied or deleted from the AXS-200/850 Ethernet Test Set

SystemEthernet Test Set 213File ManagerNote: Transferring report files can also be done using an FTP connection. Open an Internet browser and type ftt

System214 AXS-200/850VNCVNCVNC can be enabled in order for a computer running VNC Viewer to gain remote access to the AXS-200/850 Ethernet Test Set mo

SystemEthernet Test Set 215VNCTo enable VNC and connect from a computer:1. Press , select System, Utilities, and the VNC page.2. Select VNC Server and

System216 AXS-200/850VNCESC BackUp, Down, Left, Right arrowsb on keyboard (not on the NumLock keypad).Navigation ArrowsEnter SelectHomeb HomeTop numbe

SystemEthernet Test Set 217VNCThe diagram below illustrates the location and function of keys used to remotely operate the AXS-200/850 Ethernet Test S

System218 AXS-200/850Module InformationModule InformationThe Module tab contains information about the AXS-200/850 Ethernet Test Set module.Press , se

Ethernet Test Set 20114 MaintenanceTo help ensure long, trouble-free operation:³ Always clean fiber-optic connectors before using them.³ Keep the unit

Using the Smart User InterfaceEthernet Test Set 13Home MenuThe Home menu offers the following content:Home Menu Submenu Tabs/Pages1. Setupa: Allows to

Maintenance202 AXS-200/850Calibration StatementCalibration StatementAll EXFO optical products (Light Sources, Fiber-Optic Power Meters, etc) require a

MaintenanceEthernet Test Set 203Recycling and Disposal (Applies to European Union Only)Recycling and Disposal (Applies to European Union Only)³ Unless

Ethernet Test Set 22315 TroubleshootingSolving Common ProblemsBefore calling EXFO’s technical support, please read the following common problems that

Troubleshooting224 AXS-200/850Contacting the Technical Support GroupContacting the Technical Support GroupTo obtain after-sales service or technical s

TroubleshootingEthernet Test Set 225TransportationTransportationMaintain a temperature range within specifications when transporting the unit. Transpo

Ethernet Test Set 22716 WarrantyGeneral InformationEXFO Electro-Optical Engineering Inc. (EXFO) warrants this equipment against defects in material an

Warranty228 AXS-200/850LiabilityLiabilityEXFO shall not be liable for damages resulting from the use of the product, nor shall be responsible for any

WarrantyEthernet Test Set 229Service and RepairsService and RepairsEXFO commits to providing product service and repair for five years following the d

Using the Smart User Interface14 AXS-200/850Home Menu2. RFC 2544: Allows to configure the subtests and to view test results.1. Configuration: Displays

Warranty230 AXS-200/850EXFO Service Centers WorldwideEXFO Service Centers WorldwideIf your product requires servicing, contact your nearest authorized

Ethernet Test Set 231ASpecificationsIMPORTANTThe following technical specifications can change without notice. The information presented in this secti

Specifications232 AXS-200/850Ethernet CablesMinimum Category 3 cable is required for 10Base-T connection while Category 5 cable is required for 100Bas

SpecificationsEthernet Test Set 233³ Crossover Cable (10/100 Mbps)An Unshielded Twisted Pair (UTP) crossover cable is required to connect the 10Base-T

Ethernet Test Set 235B GlossaryAcronym ListABCD?HelpAC Alternating CurrentARP Address Resolution ProtocolBER Bit Error RateBERT Bit Error Rate Testbps

Glossary236 AXS-200/850Acronym ListEFGDS Differentiated ServicesDSCP Differentiated Services Code PointDTE Data Terminal EquipmentDTS Dual Test SetDUT

GlossaryEthernet Test Set 237Acronym ListHILHDTV High Definition TelevisionHz HertzICMP Internet Control Message ProtocolID IdentificationIECInternati

Glossary238 AXS-200/850Acronym ListMNlf Line FeedLOS Loss Of SignalLLA Link Local IPv6 AddressmMinutem MeterMAC Media Access ControlMbps Megabit Per S

GlossaryEthernet Test Set 239Acronym ListOPQROS Operating SystemOUI Organizationally Unique IdentifierOUT OUTputPC Personal ComputerPHY Physical Layer

Using the Smart User InterfaceEthernet Test Set 15Home Menu4. Traffic Generation & Monitoring: Traffic Generation & Monitoring test is used fo

Glossary240 AXS-200/850Acronym ListSTUssecondSC Subscriber ConnectorSDTV Standard Digital TelevisionSFP Small Form Factor PluggableSLA Service-Level A

GlossaryEthernet Test Set 241Acronym ListVVID VLAN IdentifierVLAN Virtual Local Area NetworkVoIP Voice over Internet Protocol

Glossary242 AXS-200/850VLANVLANSpecial VID values (IEEE Std 802.1Q-1998)VLAN PriorityID Description0 The null VLAN ID. Indicates that the tag header

IndexEthernet Test Set 243Index# Ping results table ... 190?...

Index244 AXS-200/850conventions, safety ... 5Copy from Throughput Test ... 74copying files ..

IndexEthernet Test Set 245HHalf ... 35Help ...

Index246 AXS-200/850Nnb of validation... 67Nb. of Frames... 58Netwo

IndexEthernet Test Set 247Graph ... 14Latency ... 14Su

Index248 AXS-200/850System menu ... 213System SettingsDate and Time ... 1

IndexEthernet Test Set 249Traffic Generation & Monitoring ... 125Transceiver Mode ... 34transport

Using the Smart User Interface16 AXS-200/850Home Menu6. Tools: Allows to ping, trace route,cable test, and report.1. Ping: Displays tabs to configure

NOTICE抩⛙CHINESE REGULATION ON RESTRICTION OF HAZARDOUS SUBSTANCES₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩NAMES AND CONTENTS OF THE TOXIC OR HAZARDOUS SUBSTANCES OR ELEMENTS CONT

MARKING REQUIREMENTS㪖㽷尐㻑Productℶ❐Environmental protection use period (years)䘾⬒≬㔳∎䞷㦮棟 ( ㄃ )Logo㪖㉦This Exfo product㦻 EXFO ℶ❐10Batterya䟄㻯aa. If applicabl

www.EXFO.com · [email protected]/N: 1057574CORPORATE HEADQUARTERS 400 Godin Avenue Quebec (Quebec) G1M 2K2 CANADATel.: 1 418 683-0211 · Fax: 1 418 683-

Using the Smart User InterfaceEthernet Test Set 17Home Menu7. Systemd: Allows file management, system settings, software options management, and displ

Using the Smart User Interface18 AXS-200/850Home MenuThe menu structure is shown as follows.TabsIf more than one page exists on the same screen, the n

Using the Smart User InterfaceEthernet Test Set 19Page ElementsPage ElementsThe title bar (blue bar) on the top of the screen is common to every page.

ContentsEthernet Test Set iiiContentsCertification Information ...

Using the Smart User Interface20 AXS-200/850Page ElementsHelpThe help button (?) displays the help information on the current page. It is possible to

Ethernet Test Set 215 Signal Connection and LEDsThis section describes all connectors (ports) and LEDs available on the AXS-200/850 Ethernet Test Set.

Signal Connection and LEDs22 AXS-200/850Electrical 10/100/1000 Mbps Ethernet PortElectrical 10/100/1000 Mbps Ethernet PortThe AXS-200/850 Ethernet Tes

Signal Connection and LEDsEthernet Test Set 23Optical 100/1000 Mbps Ethernet PortOptical 100/1000 Mbps Ethernet PortThe AXS-850-1module provide respec

Signal Connection and LEDs24 AXS-200/850Optical 100/1000 Mbps Ethernet PortLEDs for Optical PortLED Status DescriptionLASER(Red)On An optical signal i

Signal Connection and LEDsEthernet Test Set 25AXS-200/850 Ethernet Test Set LEDsAXS-200/850 Ethernet Test Set LEDsThe AXS-200/850 Ethernet Test Set di

Ethernet Test Set 276 Configuring and Starting a Test or ToolThe following procedures describe the overall steps to configure a test or tool.Configuri

Configuring and Starting a Test or Tool28 AXS-200/850Configuring a BERT TestConfiguring a BERT TestTo configure the BERT test:1. Configure the interfa

Configuring and Starting a Test or ToolEthernet Test Set 29Configuring a Traffic Generation & Monitoring TestConfiguring a Traffic Generation &

Contentsiv AXS-200/8507 Setup ...33Interface .

Configuring and Starting a Test or Tool30 AXS-200/850Configuring a Traffic Generation & Monitoring TestTo configure the Traffic Generation & M

Configuring and Starting a Test or ToolEthernet Test Set 31Configuring a Smart Loopback TestConfiguring a Smart Loopback TestTo configure the Smart Lo

Configuring and Starting a Test or Tool32 AXS-200/850Configuring a Trace Route ToolConfiguring a Trace Route ToolTo configure the Trace Route tool:1.

Ethernet Test Set 337SetupThe Setup menu is used to configure the test interface for the AXS-200/850 before it can be used for testing. The Setup menu

Setup34 AXS-200/850PortPortThe Port tab allows the selection and the configuration of the physical port. Press , select Setup, Interface, and the Port

SetupEthernet Test Set 35Port5. Select the Speed of the interface.For electrical, the choices are 10 Mbps, 100 Mbps, 1000 Mbps (requires software opti

Setup36 AXS-200/850Port7. Set the Flow Control. This option is applicable to the RFC 2544 test and Traffic Generation test. Flow Control is not suppor

SetupEthernet Test Set 37NetworkNetworkThe Network tab allows the configuration of the Ethernet port parameters.Press , select Setup, Interface, and t

Setup38 AXS-200/850Network4. If DHCP is disabled, enter the Subnet Mask for the Ethernet port. The default value is 255.255.0.0.5. Enable or disable t

SetupEthernet Test Set 39NetworkAddress: This field is configurable only when the Mode is Static. The Link-Local IPv6 Address must start with FE80. Th

ContentsEthernet Test Set v10 Traffic Generation & Monitoring ... 125Global Configuratio

Setup40 AXS-200/850Network³ Interface ID Coupled: This field is available when the Global IPv6 Address Mode is Static. This field allows to couple the

SetupEthernet Test Set 41NetworkThe Link-Local/Global IPv6 Address Status is as below:Mode Status DescriptionStatelessAuto -- UndefinedGenerating Stat

Setup42 AXS-200/850Default GatewayDefault GatewayThe Default Gateway tab allows the configuration of the default gateway address to forward packets ou

SetupEthernet Test Set 43VLANVLANThe AXS-200/850 supports up to 2 stacked layers of VLAN. The VLAN tab allows users to configure the layers, its prior

Setup44 AXS-200/850SFPSFPThe optical interface on the module is made available via a Small Form Factor Pluggable Module (SFP). For a list of supported

SetupEthernet Test Set 45Remote SelectionRemote SelectionThe AXS-200/850 can perform tests in conjunction with a second test set. A remote module can

Setup46 AXS-200/850Remote SelectionDiscoveryThe AXS-200/850 scans the subnet to discover other AXS-200/850 modules and Packet Blazer modules configure

SetupEthernet Test Set 47Remote SelectionAn icon will be displayed in the title bar if the Loop Up or the Connect operation is successful. 5. For Remo

Setup48 AXS-200/850Remote SelectionManual SelectionPress , select Setup, Remote, and the Manual Selection tab.The Manual Selection tab offers a manual

SetupEthernet Test Set 49Remote Selection³ Remote ID: The ID for the target module.³ Remote Capability: Select the Remote Capability. Choices are Remo

Contentsvi AXS-200/85014 Maintenance ...221Calibration Stat

Setup50 AXS-200/850Remote SelectionTo put the remote module into Smart Loopback or DTS RFC 2544 mode:1. Select the Remote Capability as Remote Loopbac

SetupEthernet Test Set 51ModuleModulePress , select Setup, and the Module tab.The Module page allows configuration of the following parameters:³ Modul

Setup52 AXS-200/850Save & Load ConfigSave & Load ConfigThe Save and Load Config menu allows to save the complete unit configuration and load t

SetupEthernet Test Set 53Save & Load ConfigSave, Load, Import, and Export functions are displayed on the screen when an existing configuration fil

Setup54 AXS-200/850Save & Load ConfigExport FunctionThe main aim of the export function is to copy multiple files from the Internal Flash Memory t

SetupEthernet Test Set 55Save & Load ConfigSel/Unsel All FunctionThe main aim of the Sel/Unsel All function is to select or unselect all configura

Ethernet Test Set 578 RFC 2544The AXS-200/850 allows performance testing as per RFC 2544, including Throughput, Back-to-Back, Frame Loss and Latency s

RFC 254458 AXS-200/850Global ConfigurationGlobal ConfigurationPress , select RFC 2544, Configuration, and the Global tab.³ Unit: Select the unit in Mb

RFC 2544Ethernet Test Set 59Global ConfigurationIf RFC 2544 is selected, the following frame sizes are used for IPv4 version:If RFC 2544 is selected,

Certification InformationEthernet Test Set viiCertification InformationFederal Communications Commission (FCC) and Industry Canada (IC) InformationEle

RFC 254460 AXS-200/850Global ConfigurationIf User Defined is selected, the following frame sizes are available for IPv6 version:If User Defined is sel

RFC 2544Ethernet Test Set 61Global Configuration³ Dual Test Set: Set the mode for the Dual Test Set. Choices are Remote and Local. Select either Remot

RFC 254462 AXS-200/850Stream ConfigurationStream ConfigurationPress , select RFC 2544, Configuration, and the Stream tab.³ Destination MAC Address: En

RFC 2544Ethernet Test Set 63Stream Configuration³ Destination IP Address: Enter the destination IP address. The default setting for IPv4 is 10.10.0.0,

RFC 254464 AXS-200/850Stream Configuration³ TOS/DS for IPv4 and Traffic Class (TOS/DS) for IPv6Select Type of Service (TOS) or Differentiated Services

RFC 2544Ethernet Test Set 65Stream Configuration³ If DS is selected, go to the next field to enter the hexadecimal code 00 to FF or go to the field un

RFC 254466 AXS-200/850Throughput ConfigurationThroughput ConfigurationThe objective of this test is to find the throughput of the device under test fo

RFC 2544Ethernet Test Set 67Throughput ConfigurationThe accepted values are as follows:³ Nb. of Validations: Select the number of times the result sho

RFC 254468 AXS-200/850Throughput ConfigurationNote: When the Dual Test Set parameter is set to Local in Global Configuration on page 58, the Maximum R

RFC 2544Ethernet Test Set 69Back-to-Back ConfigurationBack-to-Back ConfigurationThe objective of this test is to find the maximum number of frames tha

Certification Informationviii AXS-200/850LaserClass 1 laser product.This product complies with 21 CFR 1040.10 except for deviations pursuant to Laser

RFC 254470 AXS-200/850Back-to-Back Configuration³ Verdict Threshold: Set the threshold value in percentage of frames per burst for the test. If the de

RFC 2544Ethernet Test Set 71Frame Loss ConfigurationFrame Loss ConfigurationThe objective of this test is to find the percentage of frames that are lo

RFC 254472 AXS-200/850Frame Loss ConfigurationThe accepted values are as follows:`³ Verdict Threshold (%): Set the threshold value in percentage of fr

RFC 2544Ethernet Test Set 73Latency ConfigurationLatency ConfigurationThe objective of this test is to find the time required for the sent frame to go

RFC 254474 AXS-200/850Latency Configuration³ Maximum Rate: Enter the Maximum Rate as a percentage of the line rate or in Mbps. The accepted values are

RFC 2544Ethernet Test Set 75Summary ResultsSummary ResultsWhen the RFC 2544 test is run, a summary of the results as well as the detailed results per

RFC 254476 AXS-200/850Summary Results³ Aborted – Invalid Configuration³ Aborted – Loss of remote connectionNote: This status will appear only when the

RFC 2544Ethernet Test Set 77Summary Results³ Step: Available only for the Frame Loss subtest. This value indicates the 10 % interval of throughput dec

RFC 254478 AXS-200/850Summary ResultsResults³ Not measurable: Latency not measurable.³ Test completed³ Aborted: Aborted by user.³ Link is down³ MAC no

RFC 2544Ethernet Test Set 79Summary ResultsReport GenerationReports can be generated for the test and tools results. The report button is available on

Certification InformationEthernet Test Set ixCE Declaration of ConformityApplication of Council Directive(s): 2006/95/EC - The Low Voltage Directive20

RFC 254480 AXS-200/850Summary Results6. Press the function key under Configuration on the bottom of the screen to configure the titles and headings of

RFC 2544Ethernet Test Set 81Summary Results11. A message is displayed to indicate that the report file is successfully saved.12. Select the OK button

RFC 254482 AXS-200/850Throughput ResultsThroughput ResultsPress , select RFC 2544, Results, and the Throughput tab.³ Status: Displays the test status

RFC 2544Ethernet Test Set 83Throughput Results³ Layer: Select the layer for determining the throughput results layer to display. Choices are All, Ethe

RFC 254484 AXS-200/850Back-to-Back ResultsBack-to-Back ResultsPress , select RFC 2544, Results, and the Back-to-Back tab.³ Status: Displays the test s

RFC 2544Ethernet Test Set 85Back-to-Back Results³ Layer: Select the layer for determining the back-to-back results layer to display. Choices are All,

RFC 254486 AXS-200/850Frame Loss ResultsFrame Loss ResultsPress , select RFC 2544, Results, and the Frame Loss tab.³ Status: Displays the test status

RFC 2544Ethernet Test Set 87Frame Loss Results³ Step: Determines which step is displayed.³ Results In: The frame loss value is expressed in %. The fra

RFC 254488 AXS-200/850Latency ResultsLatency ResultsPress , select RFC 2544, Results, and the Latency tab.Note: This page is not available when the Du

RFC 2544Ethernet Test Set 89Latency Results³ Results In: The latency value is expressed in ms by default. The user can also specify the values to be d