Exfo FLS-2600B Tunable Laser Source Bedienungsanleitung Seite 19
- Seite / 157
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Tunable Laser Source 11
3 Getting Started with Your
Tunable Laser Source
Turning on the Unit
Before turning on the FLS-2600B, please read the Safety Information on
page 7.
To turn the unit on and off, use the red button in the lower left-hand corner
of the front panel. The source is not active upon startup. To activate it, see
Activating/Deactivating Light Emission on page 42.
Upon startup, the unit beeps twice, performs a self-test, and then enters the
main menu with the same settings that were active when it was shut
down. When the unit is turned off, the following items remain in a storage
device called non-volatile memory:
current power setting
current wavelength setting
current mode (normal/high resolution)
current display mode (wavelength/power)
current Setup menu settings
shortlisted wavelengths (up to 100)
sweep parameters
saved sweep configurations (up to five)
Note: The power cord is the most effective disconnecting device. To ensure that
the unit is completely turned off, disconnect the power cord.
- FLS-2600B 1
- Contents 3
- Manufacturer 7
- DECLARATION OF CONFORMITY 7
- 1 Introducing the FLS-2600B 9
- 2 FLS-2600B 10
- General Information 10
- RS-232 Connector Pinout 11
- Typical Applications 12
- IMPORTANT 13
- 2 Safety Information 15
- Electrical Safety Information 16
- Power Cable 17
- 3 Getting Started with Your 19
- Tunable Laser Source 19
- Tunable Laser Source 13 21
- 4 Setting Standard Parameters 23
- Turning the Sound On or Off 24
- Switching between Normal and 25
- High-Resolution (HR) Modes 25
- Selecting the Display Unit 26
- Selecting a Wavelength 27
- 20 FLS-2600B 28
- Setting the Power 29
- Adding Items to Lists 30
- Deleting Items from Lists 31
- Tunable Laser Source 25 33
- 26 FLS-2600B 34
- Reverting to Factory Settings 35
- 5 Setting Sweep Parameters 37
- Selecting the Sweep Mode 38
- Setting the Sweep Step 39
- Setting the Pauses 40
- Setting the Sweep Speed 41
- 34 FLS-2600B 42
- Tunable Laser Source 35 43
- Setting the Cycle Options 44
- Setting the Sweep Direction 45
- 40 FLS-2600B 48
- Starting a Sweep 51
- 7 Maintenance 53
- Use only with a 250V fuse 58
- Employer uniquement avec 58
- Software Upgrades 61
- 54 FLS-2600B 62
- Recalibrating the Unit 64
- Recycling and Disposal 64
- 8 Troubleshooting 65
- FLS-2600B-XX-XX 66
- Transportation 67
- 9 Warranty 69
- Liability 70
- Service and Repairs 72
- Tunable Laser Source 65 73
- A Technical Specifications 75
- Technical Specifications 76
- B Trigger Option Theory 77
- 70 FLS-2600B 78
- C Remote Control 79
- 72 FLS-2600B 80
- Tunable Laser Source 73 81
- 74 FLS-2600B 82
- Communication Parameters 83
- 76 FLS-2600B 84
- Bits Mnemonics Bit Value 84
- Tunable Laser Source 77 85
- 78 FLS-2600B 86
- Remote Control 87
- SCPI Commands 88
- General Commands 90
- 84 FLS-2600B 92
- 86 FLS-2600B 94
- Tunable Laser Source 87 95
- 88 FLS-2600B 96
- Tunable Laser Source 89 97
- Specific Commands 98
- DISPlay:DIMMer 99
- DISPlay:DIMMer? 99
- OUTPut:ASE? 100
- OUTPut:MODE 100
- OUTPut:MODE? 101
- OUTPut:STATe 101
- OUTPut:STATe? 102
- SOURce:MODE 102
- SOURce:MODE? 103
- SOURce:POWer:ALC 103
- SOURce:POWer:ALC? 104
- SOURce:POWer:LIMit:HIGH? 104
- SOURce:POWer:LIMit:LOW? 104
- SOURce:POWer:LIMit:STEP? 105
- SOURce:SWEep:MODE 105
- SOURce:SWEep:MODE? 106
- SOURce:SWEep:CENTer? 106
- SOURce:SWEep:COUNt 107
- SOURce:SWEep:COUNt? 107
- SOURce:SWEep:REPeat 108
- SOURce:SWEep:REPeat? 108
- SOURce:SWEep:REVerse 109
- SOURce:SWEep:REVerse? 109
- SOURce:SWEep:STARt:WAVelength 110
- SOURce:SWEep:STOP:WAVelength 111
- SOURce:SWEep:STOP:WAVelength? 111
- SOURce:SWEep:SPAN? 112
- SOURce:SWEep:SPEed 112
- SOURce:SWEep:SPEed? 113
- SOURce:SWEep:SPEed:LIMit:LOW? 114
- SOURce:SWEep:STATe 114
- SOURce:SWEep:STATe? 115
- SOURce:SWEep:DURation? 115
- SOURce:SWEep:STEP 116
- SOURce:SWEep:STEP? 116
- SOURce:SWEep:STEP:LIMit:HIGH? 117
- SOURce:SWEep:STEP:LIMit:LOW? 117
- SOURce:SWEep:PAUSe 118
- SOURce:SWEep:PAUSe? 118
- SOURce:SWEep:PAUSe:LIMit:LOW? 119
- SOURce:SWEep:TRIGger 120
- SOURce:SWEep:TRIGger? 120
- SOURce:WAVelength 121
- SOURce:WAVelength? 121
- SOURce:WAVelength:LIMit:HIGH? 122
- SOURce:WAVelength:LIMit:LOW? 122
- SOURce:WAVelength:LIMit:STEP? 123
- SYSTem:ERRor? 123
- SYSTem:VERSion? 124
- UNIT:WAVelength 124
- UNIT:WAVelength? 125
- Programming Commands 126
- 120 FLS-2600B 128
- SOURce:SWEep:STEPped:PROGram 130
- SOURce:SWEep:STEPped:PROGram? 132
- Other Commands 134
- SOURce:SWEep:RECAll? 135
- Quick Reference Command Tree 136
- Tunable Laser Source 129 137
- Tunable Laser Source 131 139
- Tunable Laser Source 133 141
- Error Messages 142
- Description Probable Cause 143
- 136 FLS-2600B 144
- Tunable Laser Source 137 145
- Tunable Laser Source 139 147
- GPIB Troubleshooting 149
- Tunable Laser Source 143 151
- Tunable Laser Source 145 153
- ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ 155
- MARKING REQUIREMENTS 156
Verwandte Produkte und Handbücher für Messgeräte Exfo FLS-2600B Tunable Laser Source
Messgeräte Exfo FG-750 Bedienungsanleitung
(338 Seiten)
(338 Seiten)
Messgeräte Exfo FVA-600 Bedienungsanleitung
(215 Seiten)
(215 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern